-
WB Aliphatic Isocyanate Prepolymer
WB Aliphatic Prepolymer is designed to be used in water-dispersible formulations. It may be used in many variations of an extremely tough optically clear weather resistant UV stable water-borne coatings. It exhibits excellent durability regarding resistance to abrasion, chemicals and sunlight.
-
Jet Epoxy
Jet Epoxy is a quick set 100% solids self leveling toughened epoxy. It provides excellent adhesive characteristics while exhibiting good chemical, moisture and UV resistance. It can be used as a primer or as a final top-coat. It may be used in confined areas as it emits very low odor emissions. This material is used on metal, wood, fiberglass, concrete, masonry and other difficult to coat surfaces requiring a tough exterior coating. It may also be formulated with anti-corrosion additives to protect ferrous metals from oxidation.
Jet Epoxy may be applied using pressure pot or air-less spray, roll-on or brush-on. This 2K epoxy system finishes glossy smooth when fully cured. This material is to be used directly on clean dry surfaces and becomes tack free within 1 hour depending on ambient humidity and temperature. It is an excellent primer backbone for all SuperSkinSystems’ super-polymers and general topcoats. It retains a wide functional temperature range while yielding good flexibility from 25F to 150F. Full cure is achieved under normal drying conditions in 24 hours.Jet Epoxy is available in 3 primary formulations:
289: clear and fast
351: low temp fast cure
319: clear slow top coatPlease contact our technical support group for specific substrate application procedures, equipment, safety gear and clean-up kits. Refer to MSDS for material and safety standard procedures.
-
JointSeal
Joint Seal is a 2-component elastomeric sealing polymer system designed to act as a crack filler primarily in concrete. This material provides exceptional adhesion characteristics and fast cure times. It is highly chemical resistant, insensitive to water, abrasion resistant and remains thermally stable in a range of -20°F (-29 C) to 250°F (125 C). It may be used under traditional floor coatings or any of our top-coating materials. Joint Seal is used in heavy traffic warehouse floors, refrigeration floors, chemical spill prone floors, pothole road repair or under ceramic tile floors. It meets FDA regulations for indirect food contact (CFR 21, Sec. 175-300). -
HardSkin
HardSkin is an industrial abrasion resistant spray coating to be used over low density substrates such as polystyrene foam and polyurethane foams which require exterior surface hardnesses up to 70 Shore D. It also provides excellent chemical and moisture resistance and is available with fire retardants to meet E84 Class I. This material is a two component 100% solids and contains no VOCs or solvents. These specialized formulations deliver optimal curing application in very cold or hot climates. HardSkin is paintable and impact resistant.
HardSkin is normally applied by a 2K high pressure plural component pumping machine with hose and primary heat set at 150F. It becomes tack free in 15-20 sec., full cure in 48 hrs. and delivers a functional temperature range of -20F to 200F. This material may also be applied by hand-held cartridge gun used at room temperature.
Please contact our technical support group for specific substrate application procedures, equipment, safety gear and clean-up kits. Refer to MSDS for material and safety standard procedures.
-
GlowSkin
GlowSkin is a durable long-lasting glow-in-the-dark harsh environment coating used primarily in safety applications providing dark dangerous areas a strong nite-light. When fully charged by the sun or auxiliary lights, the nite-light GlowSkin lasts brilliantly for 2 hours. This material is embodied ClearSkin which delivers an extremely tough weather resistant coating. It exhibits excellent durability regarding resistance to abrasion, chemicals and sunlight. Being very tough, it is used primarily in exterior high-wear environments where severe topcoat protection is required. Although GlowSkin may be used directly on many types of surfaces, it is normally used over a reflective base-coat color such as white, yellow or silver to add more to the reflective-glow. GlowSkin top-coat is available in Green and Blue. Mixing together gives a gentle aqua or light teal.
GlowSkin is a very intense high-performance glow material used in military ships, transportation subways and tunnels, amusement parks, parking decks, office building stairwells, boat docks and the art world. It provides excellent adhesive characteristics and can withstand arctic freezing or desert hot conditions.Please contact our Customer Service and Technical Support Group for any questions or to provide direction with specific selection of a material system, questionable target surfaces, operational procedures, material pumping/spray machines, spray/pour guns, safety protection gear and clean-up kits. Please refer to MSDS for material safety information.
-
I-Skin Foam
I-Skin Foam (Integral-Skin) is a high performance self-skinning foam designed for toughness and durability. Its hardness ranges from semi-rigid to sponge-soft to provide for multi-versatile applications such as commercial impact floor mats, seating cushions, vibration insulators, rigid impact panels, sports equipment, soft/rigid play toys, etc. It may be formulated in any color and many densities to accommodate very specific requirements.
This unique foam exhibits very low compression set while providing dimensional stability through its wide operating temperature range. I-Skin Foam is formulated from special MDI prepolymers to create very fast molding cycles. It is available using water or gas blown formulations. I-skin can also be formulated to meet CAL 117, MVSS 302 and FAR 25.853a
Please call or email our Technical Support Group for any questions regarding material, application or prospective uses.
-
FireSkin 1K
FireSkin™ 1K is a high temperature waterborne intumescent fire-resistant barrier coating that will withstand direct flame contact. It does not emit continuous smoke with E84 testing yielding 5=flame spread and 70=smoke during flame exposure. It is environmentally friendly and is used in demanding fire shielding applications such as mine safety, protecting steel frameworks, building foam insulation, utility poles, cedar shake roofs, styrene and polyurethane foam board and other flammable material protection. Designers also use this material’s unique decorative coating properties to enhance interior walls specified by fire-retardant requirements as acrylic texture chips may be added. 1K FireSkin also provides outstanding UV stability.
It is a water-based formulation that is applied by low pressure air-less spray equipment, roller or brush. It is non-toxic and and may be appled in low-ventilated enclosed areas. Please call or email our Technical Support Group for any questions regarding material, application or prospective uses.GlowSkin is capable of being added to Fireskin 1K.
-
FireSkin™ Foam
FireSkin Foam is an insulating material designed to withstand direct flame contact. It produces very low smoke and flame spread. The material develops an intumescent fire barrier which provides a protective shield against constant flame and extreme heat conduction to interior surfaces. These closed cell foams range in varing densities from 0.5-50 pcf for use in diverse fire protection system applications. FireSkin Foam is formulated as a Halogen-free, Class 1 fire rated foam containing renewable resource “Green” materials.
FireSkin Foam delivers toughness and dimensional stability from -20F (-29C) to 250 F (130C). It is used in a variety of construction applications such as in roof, wall and floor building insulation and structural sandwich panel construction foam core materials. These materials have been designed to accommodate HFC 245 or Pentane blowing agent for maximum R-values. This material has been designed for use in economical Continous Panel Laminator machines as shown below. See LAB FIRE VIDEO1 here. See LAB FIRE VIDEO2 here. -
FireSkin™ 2K
FireSkin 2K super-polymer is an insulating microcellular polymeric material that will withstand direct flame contact. It emits low smoke and flame spread during flame exposure making it a valuable resource for diverse fire protection enclosure applications.It has been specially designed to coat polyurethane and polystyrene foams for fire protection. Other uses include protecting buildings, humans, animals and all nature against the destructive force of fire. Uses include deployable fire barrier systems, mobile structures, hazardous containers and specialily shielding systems for schools and apartments.
Please call or email our Technical Support Group for any questions regarding material, application or prospective uses.
-
Decorative TextureCoat™
Decorative TextureCoat™ (DTC) is a tough weather resistant UV stable protective coating. It presents a decorative stucco-like texture finish which exhibits excellent durability and resistance to high wind abrasion, chemicals, staining and sunlight. This coating demonstrates a combination of many unique characteristics exhibiting excellent adhesion and penetrating capabilities securing a high performance bond to substrate. Decorative color texturing chips give this single component sprayable material a wide range of styling effects. This waterproofing exterior tough-coat may be used over diverse types of substrates such as existing stucco, concrete, brick, stone, metal, wood and composites.DTC is used as a waterproofing exterior topcoat sealer. DTC spray coating maintains good flexibility in severe hot and cold environments. It’s surface skin may be ultra-fine to medium to coarse. It is commonly used for face-lifting stucco and painted surfaces. It may also be mixed with other aggregates such aluminium oxide, walnut shells or fine stone creating anti-skid and finely styled decorative surfaces. See color textures chart for standard color blends.
Decorative TextureCoat™ is a high performance aliphatic coating with very low ordor during application. Color pigments and textures may also be added as desired. This material may also be applied directly to urethane foam materials in such applications as exterior artwork, architectural moldings or decorative facial panels.
-
Cushion Foam
Cushion Foam is a superior bio-based flexible microcellular open-cell foam designed to deliver very high toughness and durability for diverse fields of application such as furniture seating cushions, automotive seating, house-wraps, play toys, shock and vibration absorption, impact sports padding, sound-proofing, etc. Seating densities normally range from 3-5 pcf. Density formulations may be adjusted to accommodate other very specific requirements including colors.
This unique bio-based high resilient (HR) flexible foam exhibits very low compression set while providing dimensional stability through its wide operating temperature range. Cushion Foam is formulated from special MDI pre-polymers to create very fast production and de-molding cycles.
Please call or email our Technical Support Group for any questions regarding material, application or prospective uses.
-
EpoxyInjection
EpoxyInjection is a 2-component, 100% solids, toughened low-viscosity epoxy injection formulation specifically designed for in-place resin injection for cracked concreted structures such as dams, locks, canals, power plants, water reservoirs, water treatment facilities, foundations, parking garages, aqueducts, etc. This low viscosity epoxy is pumped into holes and cracks to create waterstops in weakened concrete infrastructure systems. It provides excellent adhesive characteristics while exhibiting good chemical resistance, water infiltration and exfiltration resistance. It exhibits low odor emissions, 0% VOCs, long working time, excellent cure at low temperatures and high humidities, superior hardness and low viscosity for high-penetrating injection. This material will bond to concretes, masonary and metals.
Epoxy Injection may be applied using plural component mixing pumping systems or conventional pressure pot/mix systems at a 2:1 dispensing ratio. This 2K epoxy injection material adds strength or structrual preservation to the concrete system when fully cured. Its cure times may be adjusted for specific difficult applications. It conforms to ASTM C-881, Types I, II, IV adhesive, Grade-1, Class C and AASHTO M-235 specifications.
Please contact our technical support group for specific substrate application procedures, equipment, safety gear and clean-up kits. Refer to MSDS for material and safety standard procedures.
-
70D Casting Resin
Casting Resin 70 is specifically formulated 2-component 100% solids polyurea-based materials designed to produce dimensionally stable, chemical resistant parts. This material may be pour cast, RIM injected molded or cartridge gun spray dispensed. Cured parts exhibit hardness of 70 D, excellent physical durability and chemical resistance. Casting Resin 70 reactivity is very fast with a 1-2 minute gel for fast manufacturing part cycle times obtaining full cure within 24 hours. Material shrinkage is 1%. Fillers may be added to reduce shrinkage and to provide other desired physical properties. Pigments are normally added to provide uniform appearance. Material functional operation temperature ranges from -20°F to 250°F. -
WB Aliphatic Isocyanate Prepolymer-23
WB Aliphatic Prepolymer-23 is designed to be used in water-dispersible formulations. It may be used in many variations of an extremely tough optically clear weather resistant UV stable water-borne coatings. It exhibits excellent durability regarding resistance to abrasion, chemicals and sunlight.
-
ClearSkin
Clearskin is a 100% solid aliphatic roll on coating. There are two versions available as roll on.
- 12-15 minute pot life and set to touch in 30 minutes.
- 1 hour pot life and 45 minutes set to touch.
Both produce a clear hard high gloss coating. Both 1&2 can be supplied in colors and both have excellent chemical and UV resistance. #1 has been found to have excellent electrical properties. 16 mils of coating can resist 10000 volts. Making it a great insulator.
Clearskin makes an excellent coating for steel, concrete, wood and marine applications. Its ability to cure fast with no VOCs reduces downtime to return to service. Clearskin has excellent water and chemical resistance to meet any condition. Clearskin is optically clear but can be pigmented and can have anti-corrosive additives if needed.
-
Casting Resins
Casting Resins are specifically formulated as 2-component 100% solids polyurea-based materials designed to produce dimensionally stable high temperature, high impact, chemical resistant parts. Resins are available in both hard or flexible versions and provide a dent-scratch resilient class A part surface. Flexible Casting Resin may be pour cast, RIM injected molded or cartridge gun spray dispensed. Cured materials are extremely tough and exhibit excellent durability against abrasion and cleaning chemicals. Casting Resins deliver a 1-15 minute reaction time to provide enhanced part manufacturing cycle times. Depending on the hard or semi-flexible neat formulation the material shrinkage will range from .007-.010 in./lin. in. Fillers may be added to reduce shrinkage and to provide other desired physical properties. Pigments are normally added to provide uniform appearance. Material functional operation temperature ranges from -40°F to 180°F.
-
ChemEpoxy
ChemEpoxy is a versatile fast low-temperature curing Novalac epoxy with excellent chemical resistance such as resistance to 98% sulfuric and 37% HCL acids. It provides superior resistance to water spotting, even under adverse conditions, and is DOT noncorrosive. This material is used in industrial flooring, chemically resistant tank linings, chemical handling equipment, chemical storage vessels and marine environments. It is used on metal, wood, fiberglass, concrete, masonry and other difficult to coat low temperature surfaces requiring a tough chemical resistant coating.ChemEpoxy is 2-component mixture which may be applied using roller, brush or low-pressure pot spray. This material is to be used directly on clean dry contaminant-free surfaces and becomes tack free within 1 hour depending on ambient humidity and temperature. Full cure is achieved under normal drying humidity in 7 days at ambient temperature.
Please contact our technical support group for specific substrate application procedures, equipment, safety gear and clean-up kits. Refer to MSDS for material and safety standard procedures.
-
WB Modified Polyols
WB Acrylic Modified Polyols are designed to be used in 2K waterborne coating formulations. These polyols when reacted with aliphatic isocyanates exhibit excellent durability regarding resistance to abrasion, chemicals and sunlight. They may also create an optically clear high gloss or matte finish which is available in rigid or flexible versions. WB Acrylic Modified Polyols materials may be color pigmented for solid or translucent appearance.
These 70% solids acrylic polyols are avaiable in 2 euqivalent weights. These polyols are intended to be used with WB aliphatic prepolmers such as WB Prepolymer-16 or WB Prepolymer-23. SuperSkinSystems offers a large range of WB Aliphatic Prepolymers form many customized coating formulations.
Recommended storage conditions are to protect from frost and high heat, temperature range: 45-120 F (7-49 C) and kept in tightly closed containers no longer than 12 months. KEEP FROM FREEZING. Please refer to MSDS for Product Safety and Regulatory information.
-
5000-2.5 TRX Pouring Foam
5000-2.5 TRX pouring foam is a water-blown foam designed especially for pour casting into molds to create very intricate very diverse parts. This pouring foam is blended to specifically designed re-activity molding times such as creme time, gel time, tack-free and overall cure time. The foam contains a bio-based polyol. This pour casting foam may be used in a variety of applications in very diverse industries such as architectural wall and decorative part moldings, furniture and toy markets, specialty part moldings etc.
Please contact our Customer Service and Technical Support Group for any questions or to provide direction with specific selection of a material system, questionable target applications, operational procedures, material pumping/pour machines, safety protection gear and clean-up.
-
BlastSkin II – Mine Safety
BlastSkin II- Mine Surface Protection System is a very strong super-polymer coating system designed to provide structural support while shielding against water and methane infiltration for all surfaces in the mine. This system provides high chemical, abrasion resistance, low fire and smoke meeting Class 1 ASTM E84, MSHA ASTM E162, Radiant Panel testing and MSHA IC-249 Flame resistance of solid products. The BlastSkinII protection system effectively delivers increases load bearing capacity and reduces localized failure points to defend against rupture and bursting. This high-strength composite structure provides added protection to mine workers, framework infrastructure and overall mine safety.
Mine Surface Protection System:
- Inject LeakStop into all surface cracks and voids.
- Spray structural FireSkin™ Foam (10 pcf) on mine surfaces (25mm).
- Apply BlastSkinII super-polymer over the structural FireSkin Foam (3mm to 6mm).
- Apply GlowSkin striping to walls (0.5mm).
-
Aliphatic Prepolymers (APU Series)
The APU Series is a new family of HDI aliphatic prepolymers using polyurea technology. All prepolymers are monomer extracted to levels of 0.1%. The prepolymers are available from 6% to 20% NCO. Specifically designed or custom Prepolymers may be manufactured for client needs. All prepolymers are 100% solids. These prepolymers may be supplied with solvents upon request. The APU # indicates the % NCO. APU-16 is one our standard workhorse prepolymers in polyurea formulations and well as in the polyaspartic series of products to deliver specific performances.
-
APA
APA is a new revolutionary, zero VOC, non-conventional exterior, 100% polyurea coating. This product has been designed specifically to deliver the toughness and abrasion resistant properties of that of an aromatic polyurea but provides the capability of retaining color-fastness for a full range of pigmented colors. Unlike conventional aromatic polyurea, which in a white pigmented system turns yellow in hours when left in direct sun light, APA systems can withstand direct harsh sunlight experiencing no color change after 1 year. APA is available with different hardness and reactivities. APA is available in 2 versions – horizontal and vertical. Horizontal APA has a gel time of approximately 30-45 seconds allowing the ability to broadcast into it if desired, whereas Vertical APA is a quick set material allowing to be sprayed vertically without running. APA has excellent adhesion properties allowing it to be sprayed on all types of surfaces including spray foams. APA complies with FDA 21CFR 175.105 and 21 CFR 175.300. APA is also available with fire retardant additives. These additives allow APA to meet ASTM E84 Class A. APA uses a mix ratio of 1A – 1B. APA may be applied using high pressure heated plural equipment, low pressure heated equipment or using cold spray 2K cartridge equipment. Recommended heater settings are 140°F for both primary heaters and hose heater. Machine pressure should be set at around 2000 psi.
-
Anti-Graffiti Coating
Anti-Graffiti coating represents a new class of tough thin and durable advanced polymers. This easy to apply coating turns ordinary walls and ceilings into a cleanable canvas of art. It’s unique physical properties give it superior cleanability and resistance to Sharpie solvent markers and most paints. Universal rubbing alcohol is used as the cleaner fluid with a dry clean rag. The Anti-Graffiti Coating is used on school room walls to replace blackboards and dry erase boards, subway walls and ceilings to provide easier paint removal, hospital walls and floors to enable easy clean up sanitary surfaces, protect outdoor building walls, steel and concrete bridges members, public bathroom walls and any surface indoor or out which requires graffiti protection or to aid in cleaning.
This 70% solids 2-component coating is water based and therefore is easy to clean up using soap and water. It is easily applied using roller, air-less spray machine or brush. Pot life after mixing is 30 minutes with air dry tack free surface time of 45 minutes depending on ambient humidity. It may be formulated in just about any color or clear as its natural state. It exhibits a high functioning temperature of 220°F, excellent abrasion and outdoor UV stability. It remains flexible at 0°F and can withstand light mild solvent attack. Given this materials extraordinary clean-ability and durability characteristics it lends itself to many diverse demanding applications.
Please call or email our Technical Support Group for any questions regarding material, application or prospective uses.
