-
FireSkin™ Foam 0.5
Fireskin Foam 0.5 is a two component, 1-1 parts by volume, light density, spray applied polyurethane foam. To produce Fireskin Foam 0.5 requires the use of an A-Component (ISO) and a B-Component (RESIN), which contains zero ozone depleting blowing agents, catalyst, polyols and flame-retardant materials such as fiberglass, cellulose or other loose fill products. Typical areas where spray polyurethane foam is applied are interior walls, attics, ceilings and spa insulations.
-
Ground Glass Powder
SSS Ground Glass Powder is made from 100% recycled glass occurring in laminated glass (primarily automotive windshields). The product is gray colored powder with a uniform particle size distribution. SSS Ground Glass Powder is amorphous and contains no crystalline silica and provides a clean post-consumer filler for polymer-based systems. This filler impart excellent abrasion resistance and chemical stability to coatings and other polymer systems. SSS Ground Glass Powder processing system provides consistent product quality with fineness covering a range of potential applications. Product is screened and shows average size particles of Mesh 325.
-
Silicone Epoxy
Silicone Epoxy is a high temperature epoxy with excellent chemical resistance. It provides superior resistance to water spotting, even under adverse conditions and is DOT noncorrosive. This material is used in industrial flooring, chemically resistant tank linings, chemical handling equipment, chemical storage vessels and marine environments. It is used on metal, wood, fiberglass, concrete, masonry and other difficult to coat surfaces requiring a tough chemical resistant coating. Silicone Epoxy is optically clear and has excellent UV Resistance. It has outstanding temperature resistance allowing it to be used up to 400°F.
-
WBSE-3
WBSE-3 is the next version of our WBE-2. It has the same characteristics as WBE-2 with long pot life up to 8 hours after mixing A & B, tack free times of under 20 minutes, fast cure times in 16 mil or less film thickness, but has a Silicone backbone built into the Hardener. This enables the WBSE-3 to have higher temperature better chemical, higher gloss, optically clear and better UV resistance.
WSBE-3 can also come with Nano size glass filler similar to WBE-2. Glass filled WBSE-3 has a matte finish and non-skid surface. The ratio of Resin to Hardener is 1 resin to 1 hardener without glass. The glass is premeasured so it an be added to the A&B mix with a jiffy mixer. WBSE-3 can be used on concrete, asphalt, steel, aluminum, and wood. Colors are available, simply send in a pantone, RAL, or SW color number. Surface preparation is still the same as WBE-2. Like all water based products freeze protection is required for shipping.
Please contact our technical support group for specific substrate application procedures, equipment, safety gear and clean-up kits. Refer to SDS for material and safety standard procedures.
WBE-3 can withstand up to 5 freeze/thaw cycles
-
WBE-2
WBE2 is a clear or pigmented 2- component water based aliphatic epoxy formulation with excellent chemical and UV resistance. WBE2 has great adhesion to most substrates such as concrete, metals and asphalt. There is no odor or vocs allowing it to use for inside applications. It is available with 50% nano size glass filler , anti static , anti-microbial, and anti-corrosive additives. WBE2 can be used as a primer and can be diluted with 25% water to penetrate porous concrete. WBE2 dries to a high gloss top coat . The glass filled dries to a matte finish with a nonskid finish.
WBE2 dries very fast depending on temperature , humidity and thickness. Typical drying times are 15 minutes with up to 8 hour pot life. WBE2 may be sprayed, brushed or rolled. Tack free at 75F is 15-30 minutes. At temperatures of 50F tack free times maybe 2 hours. Rolling should be done with a short knap roller. Typical use temperatures are between 25-150F . Full cure should be 24 hours.
WBE2 can be made with ESD ( electric static discharge) additives. Its available in clear or pigmented. Unlike other ESD resins which use carbon fibers , WBE2 does not need them . ESD materials are used in clean rooms or where sparks may cause serious problems.
Please contact our technical support group for specific substrate application procedures, equipment, safety gear and clean-up kits. Refer to SDS for material and safety standard procedures.
-
RailSkin™
RailSkin™ polyurea is an extremely tough abrasion resistant super-polymer designed to protect the interior of steel or aluminium rail cars which are used to haul harsh aggregates such as coal, rock, salt, land-fill materials, etc. This 2k 1A:1B material provides superior tear and impact strength while delivering a high degree of corrosion resistance. RailTuff is a non-breathable polyurea which eliminates water vapor transmission to underlying surfaces to prevent the undelying metals from oxidizing. RailSkin may also be used in many other industrial and harsh environments.
Please contact our Technical Support Group for any technical questions regarding material, application or prospective uses.
-
WBE-2 Primer
WBE-2 Primer is a clear or pigmented fast drying two-component aliphatic epoxy primer designed to promote excellent adhesion performance with no odor during interior application. It is available in hard or flexible formulations. It may be directly topcoated using many SuperSkinSystems coatings within a 48 hours period.
WBE-2 Primer may be used on many substrates such as steel, aluminium, fiberglass, concrete masonary and wood. It also may be formulated to include anti-corrosive properties for all oxidizing substrates. This special formulated primer may be applied to slightly damp surfaces. Full cure is achieved under normal conditions in 24 hours.
Please contact our technical support group for specific substrate application procedures, equipment, safety gear and clean-up kits. Refer to SDS for material and safety standard procedures.
-
Sealer-9
Sealer-9 is a flexible one-component 9% NCO isocyanate based sealer used primarily for sealing concrete and other porous cementuous substrates. It provides a tough moisture-curing penetrating film which may be solvent reduced up to 40% using Xylene, Naptha Aromatic 100, Butyl Acetate or MEK.
Sealer-9 is applied in thin wets coats and quickly flashes off to a dry-tacky touch in minutes depending on relative humidity and temperature. Please contact our technical support group for specific substrate application procedures, equipment, safety gear and clean-up kits. Refer to SDS for material and safety standard procedures.
-
Primer 30
Primer 30 is a unique single component multi-purpose penetratrating primer to be used to support all SuperSkinSystems’ topcoat systems. It provides excellent sealing capabilities on porous and non-porous substrates such as concrete, wood, stucco, metals, fiberglass, non-glazed tile, old painted surfaces, oxidized epdm membranes, masonary, plaster, etc. The primer is ready to use and does not require the use of solvents such as Primer 28. Material fast cure Mek 1:1 slow aromatic 100. It is very robust and versatile and can be applied to not so perfectly prepped surfaces although the sufaces still be cleaned from contaminates such as oils, loose debris, dirt, waxes, etc. In general, this all-purpose primer delivers optimum adhesive characteristics combined with an extended window of application time prior to the application of topcoats. This primer may also be formulated with corrosion inhibitors is desired. Please contact our technical support group for specific substrate application procedures, equipment, safety gear and clean-up kits. Refer to MSDS for material and safety standard procedures.
-
MACE-Flex
Mace-Flex is an aliphatic 1-component self-crosslinking waterborne formulation delivering excellent chemical and water resistance while providing good abrasion resistance and fast-setting properties.
Mace-Flex or Mace-Regular is designed to be solvent-free and used as a tough exterior topcoat, sealer or as an underlying penetrating primer. The penetrating nature of this material promotes its use for direct topcoating on porous and non-porous substrates masonary, wood, non-glazed tile, stucco, metal, composites and certain polymers. These materials may also be used as a primer in many SuperSkin System’s coating applications.Mace is an air-dry system where it is normally spray or roll applied. This low viscosity dispersion dries clear and flexible in 10-15 minutes acquiring full-cure in 24 hrs or maybe forced dried at elevated temperatures. Mace-Flex provides up to 200% elongation with a tensile strength of 2400 psi. Acrylic color pigments and thickener additives may also be included to enhance its widely diversified use.
-
MACE-Regular
Mace-Regular is an aliphatic 1-component self-crosslinking waterborne formulation delivering excellent chemical and water resistance while providing good abrasion resistance and fast-setting properties.
Mace-Regular is designed to be solvent-free and used as a tough exterior topcoat, sealer or as an underlying penetrating primer. The penetrating nature of this material promotes its use for direct topcoating on porous and non-porous substrates masonary, wood, non-glazed tile, stucco, metal, composites and certain polymers. These materials may also be used as a primer in many SuperSkin System’s coating applications.
Mace-Regular is an air-dry system where it is normally spray or roll applied. This low viscosity dispersion dries clear and flexible in 10-15 minutes acquiring full-cure in 24 hrs or maybe forced dried at elevated temperatures. Mace-Flex provides up to 200% elongation with a tensile strength of 2400 psi. Acrylic color pigments and thickener additives may also be included to enhance its widely diversified use.
