-
Ground Glass Powder
SSS Ground Glass Powder is made from 100% recycled glass occurring in laminated glass (primarily automotive windshields). The product is gray colored powder with a uniform particle size distribution. SSS Ground Glass Powder is amorphous and contains no crystalline silica and provides a clean post-consumer filler for polymer-based systems. This filler impart excellent abrasion resistance and chemical stability to coatings and other polymer systems. SSS Ground Glass Powder processing system provides consistent product quality with fineness covering a range of potential applications. Product is screened and shows average size particles of Mesh 325.
-
HardSkin
HardSkin is an industrial abrasion resistant spray coating to be used over low density substrates such as polystyrene foam and polyurethane foams which require exterior surface hardnesses up to 70 Shore D. It also provides excellent chemical and moisture resistance and is available with fire retardants to meet E84 Class I. This material is a two component 100% solids and contains no VOCs or solvents. These specialized formulations deliver optimal curing application in very cold or hot climates. HardSkin is paintable and impact resistant.
HardSkin is normally applied by a 2K high pressure plural component pumping machine with hose and primary heat set at 150F. It becomes tack free in 15-20 sec., full cure in 48 hrs. and delivers a functional temperature range of -20F to 200F. This material may also be applied by hand-held cartridge gun used at room temperature.
Please contact our technical support group for specific substrate application procedures, equipment, safety gear and clean-up kits. Refer to MSDS for material and safety standard procedures.
-
I-Skin Foam
I-Skin Foam (Integral-Skin) is a high performance self-skinning foam designed for toughness and durability. Its hardness ranges from semi-rigid to sponge-soft to provide for multi-versatile applications such as commercial impact floor mats, seating cushions, vibration insulators, rigid impact panels, sports equipment, soft/rigid play toys, etc. It may be formulated in any color and many densities to accommodate very specific requirements.
This unique foam exhibits very low compression set while providing dimensional stability through its wide operating temperature range. I-Skin Foam is formulated from special MDI prepolymers to create very fast molding cycles. It is available using water or gas blown formulations. I-skin can also be formulated to meet CAL 117, MVSS 302 and FAR 25.853a
Please call or email our Technical Support Group for any questions regarding material, application or prospective uses.
-
Jet Epoxy
Jet Epoxy is a quick set 100% solids self leveling toughened epoxy. It provides excellent adhesive characteristics while exhibiting good chemical, moisture and UV resistance. It can be used as a primer or as a final top-coat. It may be used in confined areas as it emits very low odor emissions. This material is used on metal, wood, fiberglass, concrete, masonry and other difficult to coat surfaces requiring a tough exterior coating. It may also be formulated with anti-corrosion additives to protect ferrous metals from oxidation.
Jet Epoxy may be applied using pressure pot or air-less spray, roll-on or brush-on. This 2K epoxy system finishes glossy smooth when fully cured. This material is to be used directly on clean dry surfaces and becomes tack free within 1 hour depending on ambient humidity and temperature. It is an excellent primer backbone for all SuperSkinSystems’ super-polymers and general topcoats. It retains a wide functional temperature range while yielding good flexibility from 25F to 150F. Full cure is achieved under normal drying conditions in 24 hours.Jet Epoxy is available in 3 primary formulations:
289: clear and fast
351: low temp fast cure
319: clear slow top coatPlease contact our technical support group for specific substrate application procedures, equipment, safety gear and clean-up kits. Refer to MSDS for material and safety standard procedures.
-
JointSeal
Joint Seal is a 2-component elastomeric sealing polymer system designed to act as a crack filler primarily in concrete. This material provides exceptional adhesion characteristics and fast cure times. It is highly chemical resistant, insensitive to water, abrasion resistant and remains thermally stable in a range of -20°F (-29 C) to 250°F (125 C). It may be used under traditional floor coatings or any of our top-coating materials. Joint Seal is used in heavy traffic warehouse floors, refrigeration floors, chemical spill prone floors, pothole road repair or under ceramic tile floors. It meets FDA regulations for indirect food contact (CFR 21, Sec. 175-300). -
MACE-Flex
Mace-Flex is an aliphatic 1-component self-crosslinking waterborne formulation delivering excellent chemical and water resistance while providing good abrasion resistance and fast-setting properties.
Mace-Flex or Mace-Regular is designed to be solvent-free and used as a tough exterior topcoat, sealer or as an underlying penetrating primer. The penetrating nature of this material promotes its use for direct topcoating on porous and non-porous substrates masonary, wood, non-glazed tile, stucco, metal, composites and certain polymers. These materials may also be used as a primer in many SuperSkin System’s coating applications.Mace is an air-dry system where it is normally spray or roll applied. This low viscosity dispersion dries clear and flexible in 10-15 minutes acquiring full-cure in 24 hrs or maybe forced dried at elevated temperatures. Mace-Flex provides up to 200% elongation with a tensile strength of 2400 psi. Acrylic color pigments and thickener additives may also be included to enhance its widely diversified use.
-
MACE-Hard
MACE-Hard is an aliphatic 1-component waterborne formulation delivering excellent chemical and water resistance while providing good abrasion resistance and fast-setting properties. MACE-Hard is also available without solvent. This material is designed to be used as a tough exterior topcoat, sealer or as an underlying penetrating primer. The penetrating nature of these materials promotes its use for direct topcoating on porous and non-porous substrates masonry, wood, non-glazed tile, stucco, metal, composites and certain polymers. This material may also be used as a primer in many SuperSkin System’s coating applications. MACE-Hard is an air-dry system where it is normally spray or roll applied. This low viscosity dispersion dries clear in 10-15 minutes acquiring full-cure in 24 hrs or maybe forced dried at elevated temperatures. Acrylic color pigments and thickener additives may also be included to enhance its widely diversified use.
-
MACE-Hard-SF
Mace-Hard-SF is an aliphatic 1-component waterborne formulation delivering excellent chemical and water resistance while providing good abrasion resistance and fast-setting properties. MACE Hard is also available without solvent Mace-Hard-SF and both are designed to be used as a tough exterior topcoat, sealer or as an underlying penetrating primer. The penetrating nature of these materials promotes its use for direct topcoating on porous and non-porous substrates masonary, wood, non-glazed tile, stucco, metal, composites and certain polymers. This material may also be used as a primer in many SuperSkin System’s coating applications. Mace-Hard is an air-dry system where it is normally spray or roll applied. This low viscosity dispersion dries clear and flexible in 10-15 minutes acquiring full-cure in 24 hrs or maybe forced dried at elevated temperatures. Acrylic color pigments and thickener additives may also be included to enhance its widely diversified use.
-
MACE-Regular
Mace-Regular is an aliphatic 1-component self-crosslinking waterborne formulation delivering excellent chemical and water resistance while providing good abrasion resistance and fast-setting properties.
Mace-Regular is designed to be solvent-free and used as a tough exterior topcoat, sealer or as an underlying penetrating primer. The penetrating nature of this material promotes its use for direct topcoating on porous and non-porous substrates masonary, wood, non-glazed tile, stucco, metal, composites and certain polymers. These materials may also be used as a primer in many SuperSkin System’s coating applications.
Mace-Regular is an air-dry system where it is normally spray or roll applied. This low viscosity dispersion dries clear and flexible in 10-15 minutes acquiring full-cure in 24 hrs or maybe forced dried at elevated temperatures. Mace-Flex provides up to 200% elongation with a tensile strength of 2400 psi. Acrylic color pigments and thickener additives may also be included to enhance its widely diversified use.
-
Pole-Setting Rigid Foam
Pole Setting Foam is designed specifically for fast-setting structural pole-setting applications such as utility/telephone poles, flag poles, fence posts, etc. It is a tough 100% solids non-hydrophilic 6 pcf foam formulation exhibiting 100 psi compressive strength to provide secure fast-installations. The foam may be used directly in holes which contain a water volume of less than 5% of the total hole volume. It delivers excellent chemical resistance and may be applied in dirt having a wide pH range. For special applications a 9.0 PCF density is also available with the same characteristics, but higher compression strength.
Pole-Setting Foam is mixed 1:1 using a hand-held drill jiffy mixer until both components mix into a uniform color (approx 1min). It is then poured directly around the pole into the surrounding hole which obtains a firm material set-up within 15 minutes. The foam may be covered with dirt immediately after it becomes rigid to the touch. It will not be damaged by rain after this point. Material reactivity time may be adjusted to accommodate specific demanding application environments if requested. Please contact Customer Service/ Tech Support for application recommendations and procedures.
